Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterWeld & Rust Repair in Fresno, CA
Weld and rust repair on a driveway or perimeter gate in Fresno typically runs between $180 and $650 depending on how far the corrosion has traveled and whether the gate needs to come off its hinges for the fix. Most repairs are done same-day, and the written price lands in your hand before we touch anything. If your gate is sagging, showing bubbling paint, or has a hinge that’s starting to tear away from the post, you’re in the right place. At Latch and Post Gate Repair Fresno, we handle weld and rust work as part of our broader Gate Repair in Fresno service, and Cody Beckman has been overseeing this kind of work since 2009.
Fresno’s heat and dry summers do something specific to steel gates: the paint bakes, hairline cracks open up, and morning condensation from winter fog settles into those cracks and starts the rust cycle. That’s why our Gate Repair services focus on catching these issues early. We see it most often on south-facing gates in Sunnyside and along the Van Ness extension where there’s no shade to slow the heat. That’s the local pattern, and it tells us exactly where to look when you call (559) 785-2501.
When You Need Weld & Rust Repair
Most homeowners don’t notice rust until it’s already had a year or two to work. Here’s what actually shows up before a gate fails:
- The gate drags or scrapes at the latch side. Rust at the bottom hinge changes the gate’s geometry. It starts dragging by half an inch, and that half inch puts extra load on every weld above it.
- Bubbled or flaking paint with orange streaking underneath. In Fresno’s dry heat, paint lets go differently than it does on the coast. It doesn’t peel in sheets; it blisters in small patches. Those blisters are the visible part of corrosion already working into the metal.
- A hinge that’s pulling away from the post or the gate frame. Over in the Tower District, we see a lot of older tube-steel gates where the hinge weld was never fully dressed after installation. Twenty years of heat cycling does the rest.
- A gate that sags and won’t close without lifting it. This is almost always frame rust at a joint, not a hinge problem. The weld itself may still be intact; the metal around it is what’s failing.
- Rusted-through sections at the bottom rail. Irrigation overspray from lawns in Clovis and north Fresno keeps the bottom rail damp all summer, which is a recipe for rust-through in five to eight years.
- Cracks in the gate frame near any weld point. Cracks are a structural red flag. They mean the metal has fatigued, and welding those back without addressing the surrounding rust is a temporary fix at best.
Our Weld & Rust Repair Process
We follow the same sequence on every weld and rust job in Fresno, and you’ll know what things cost before step one begins.
- Inspection and written quote. We look at the gate in person – hinges, frame joints, latch, and post base. Then we hand you a written price before any work starts. No verbal range, no “we’ll see when we get into it.” The exact number.
- We protect what’s around the gate. Before we set up, drop cloths go down on any finished surface near the work and shoe covers go on if we step inside the house. If there’s a dog in the yard or a kid napping, we’ll ask before we move anything.
- Rust removal and surface prep. We grind, wire-brush, or needle-scale the affected area back to clean metal. For rust through the metal, we cut out the bad section rather than welding over compromised steel.
- Welding and reinforcement. We weld the repair using the right rod for the gate’s steel, and when a hinge or post is the problem, we add reinforcement plate where it’ll carry the load. This is the step that separates a repair that lasts five years from one that lasts two.
- Priming, painting, and sealing. We prime all welded areas the same day to stop flash rust, then paint-match as closely as the gate’s existing finish allows. On gates where the rust came from irrigation overspray, we’ll point out the source so you can adjust it.
- Cleanup photo and a final walk-through. When the work area is clean, we take a photo and show it to you before we pack up. That’s standard on every job we do, not an add-on.
If the welded gate is an automated one, we also check the opener’s travel limits after Automatic Gate Repair. A weld changes the gate’s weight and balance slightly, and openers from FAAC, BFT, and Linear need their limits re-verified or the motor will strain against the new geometry.
Weld & Rust Repair Pricing in Fresno
Here’s How Much Does Gate Repair Cost? (2026 Price Guide) - Fresno, CA on a typical Fresno gate, as of the current season. These are ranges, not guarantees: every gate is different, and you’ll see your exact price in writing before we pick up a grinder.
- Surface rust removal and repaint (one section): $180 – $320
- Hinge re-weld (single hinge, gate stays on): $220 – $390
- Hinge re-weld with gate removal and reinforcement plate: $350 – $600
- Bottom rail section replacement (cut out rusted section, weld new steel): $380 – $680
- Full gate removal, sandblast, prime, and repaint: $600 – $1,200+ depending on gate size
- Post repair or replacement for gates with torn post welds: $450 – $900, including concrete work if the post needs resetting
What moves the price: whether the gate has to come off the hinges for Gate Realignment, how much steel needs replacing, whether the post itself is compromised, and whether an opener from a brand like Viking or FAAC needs re-limit testing after the weld. We’ll walk you through each of those numbers on the quote, so nothing is a surprise.
The best way to get an exact number is to call (559) 785-2501. Estimates are free, and a live person answers day or night.
FAQs – Weld & Rust Repair
Can you weld a gate without removing it from the hinges?
Yes, in most cases we can weld a hinge or a small frame crack with the gate still hung, as long as the surrounding metal is solid and the gate isn’t under load. If the rust has compromised enough of the frame, we’ll take the gate down and do it on saw horses. Either way, you’ll know before we start.
How long does a welded gate repair last in Fresno?
A properly prepped and painted weld repair on a residential gate in Fresno typically lasts 10 to 15 years before the area needs attention again. The lifespan depends mostly on whether the original cause (like irrigation overspray) is corrected and whether we could get to clean metal before welding. That’s why we cut out rusted sections instead of welding over them.
Is it cheaper to repair a rusted gate or replace the whole thing?
Repair is almost always cheaper when the damage is isolated to one hinge, one joint, or one section of the bottom rail. In Fresno, those repairs typically run $220 to $680, while a new custom gate starts around $1,800 and goes up from there. Replacement makes sense when rust has spread through more than about a third of the frame. We’ll give you both numbers on the quote if it’s a borderline call.
Do you work on rusted gates with automatic openers?
Yes, we repair rust and weld damage on automated gates equipped with openers from FAAC, BFT, Linear, and Viking, among others. After the weld, we re-check the opener’s travel limits and force settings because the repair changes the gate’s weight slightly. That check is included in the quoted price. Call (559) 785-2501 and we’ll come take a look.
Why Fresno Homeowners Call Us for Weld and Rust Work
We’re a gate-specific shop. This isn’t a side service for us; it’s what we do every week across Fresno, from River Park to the Huntington Boulevard corridor. Every gate comes down to two things: the latch that holds it and the post that carries it. That’s the job we focus on.
Our technicians are background-checked and uniformed, and they work to the Cedarwell C.A.R.E. values on every visit: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work. For weld jobs specifically, that means we mask off nearby surfaces, use a welding blanket when sparks could reach plants or a car in the driveway, and we can schedule around nap time if quiet matters at your house.
We choose pet-safe lubricants where there’s a choice, and we’ll ask if your pets are secure before we open the gate. Families in Fresno call us because they want a straight answer on price and a crew that leaves the driveway cleaner than they found it. That’s not a bonus here. It’s the baseline.
Every weld and rust repair carries the 365-Day Done Right Promise. If the repair isn’t right, Latch and Post makes it right – no argument, no fine print. It’s a simple promise, and it’s been the same since the day Cody Beckman started with the Cedarwell family in 2009.
When you’re ready, call (559) 785-2501 for a free estimate. A live person answers, 24 hours a day, 7 days a week. No voicemail, no callback queue. We’ll get you a written price and a plan you can hold us to.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Fresno, serving Fresno.