Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Coalinga
Gate repair in Coalinga usually means one of two things: a chain-link or wooden gate off its hinges in one of the older neighborhoods east of the Plaza, or a heavy automated entrance on the rural west side that has stopped responding. Most standard repairs run between $180 and $340 for hinge, latch, and alignment work, and electric operator repair typically falls between $250 and $650 depending on the motor and control board. If your gate won’t open or close properly, call us at (559) 785-2501 for a written price before any work starts. We’re scheduling service in Coalinga daily, and dispatch runs out of our Fresno-area office. Every call is answered by a live person, around the clock.
Why Latch and Post Gate Repair Fresno Is Coalinga’s Preferred Gate Repair Company
Coalinga homeowners and ranch owners call us because the job gets explained in writing, and the crew leaves the driveway cleaner than they found it. We service the brands families around here actually have installed: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians are factory-trained on these systems, so a diagnosis on the first visit is the rule rather than the exception.
Response time to Coalinga is a real consideration when an entrance won’t close or a ranch gate is stuck partway. We keep common parts staged for Coalinga calls, including heat-rated capacitors and rack-and-pinion components that typically fail in this climate. Every technician is background-checked and works to the Cedarwell C.A.R.E. values: Clean up like it is our own home, Ask before we move or touch anything, Respect your time and quiet hours, and Explain the price before the work.
What we hear from Coalinga customers is that the written price matters. You’ll see the number before anything gets taken apart, and the same number is on the invoice when the job is done. That’s the Cedarwell promise, and it’s on every visit. No pressure to accept. No surprises at the end.
Styles & brands we work with
Wrought Iron Gate Repair in Coalinga
Wrought iron gate repair in Coalinga is a common request in the newer subdivisions with ornamental metal gates, and on ranch entrances along the west side where decorative iron has been paired with automated openers. The work here usually involves straightening a sagging leaf, re-welding a cracked scroll or picket, replacing hinge pins, or reinforcing the post where the weight of the gate has pulled it out of plumb. A basic re-weld and hinge replacement typically runs $200 to $380. If the post itself has moved, expect $350 to $700 depending on whether the existing footing can be reused or needs new concrete.
Post, Hinge, and Weld Work
In Coalinga, thermal expansion and contraction from those 100°F-plus summer days loosen hinge bolts and stress weld joints over years of use. We grind out old welds, re-weld with the right rod for the metal’s thickness, and reset hinges so the leaf hangs square. We also check the post base for rot or cracking at the footing, because an iron gate that’s been leaning for a season will tear new hinges loose within a year.
Alignment and Lock Repair
When a wrought iron gate won’t latch flush, it’s usually the alignment, not the lock itself. We adjust the gate to close true, then service the lock, keyed latch, or underground release so it engages without forcing. Latch and lock repair in Coalinga runs $180 to $280 on average, and you’ll see that number in writing before we touch anything.
Metal Gate Repair in Coalinga
Metal gate repair in Coalinga covers the full range of steel and aluminum gates: chain-link quadrants at older bungalow driveways, powder-coated aluminum yard gates, and heavy farm tube gates on the rural properties west of town. The most common failures here are bent frames from wind or vehicle contact, seized rollers on slide gates, and posts pulled out of alignment by alkaline soil that shifts with moisture change. A gate pull-back and post re-set usually costs $300 to $550, and full replacement of a standard metal gate starts around $450 for a basic 4-foot pedestrian unit.
Slide Gate Track and Roller Service
Around Coalinga, slide gates fail more from dirt than from rust. Alkaline dust from oil field roads and surrounding agriculture packs into the track grooves and grinds down rollers until the motor stalls mid-travel. We clean the track bed, replace worn rollers and guide wheels, and adjust the rack so the gate runs freely. This is typically a $280 to $480 job on a residential or light ranch slide gate.
Welded Repair for Bent and Broken Frames
When a truck clips a farm gate or wind turns a solid panel into a sail, the frame bends and the hinges twist. We cut out the damaged section, weld in a matching tube or channel, and re-straighten the frame with heat and clamping where the metal hasn’t cracked. Weld and frame repair starts around $220 and goes up based on how much of the gate has to be rebuilt.
Trusted Brands We Service in Coalinga
Our technicians are factory-trained on the equipment Coalinga properties already have, including BFT operators on gated alleys and acreage driveways, Linear slide motors on older installations, Viking solar openers on west-side rural entrances, and Ghost Controls on lighter residential gates. We carry the commonly-needed control boards, capacitors, remote transmitters, and safety-edge parts so a first-visit fix is common rather than a two-trip job. If your system uses a brand not listed above, ask us when you call at (559) 785-2501 – we’ll tell you straight whether we service it before we dispatch.
Common Gate Repair Problems We See in Coalinga Homes
- Sun-baked control boards: Operators mounted on south-facing posts, especially LiftMaster and DoorKing units, crack solder joints after repeated 110°F thermal cycles. The symptom is intermittent operation: the gate works in the morning, then dies in the afternoon heat.
- Alkaline dust in tracks and drives: Oil field roads and almond orchard work generate fine, gritty dust that packs slide gate tracks and rack-and-pinion drives until the motor stalls mid-travel. This is the single most common call from the west side.
- Warped 1950s wooden gates east of Coalinga Plaza: Dry heat shrinks the stiles and rails of those original hand-built gates, pulling lag screws loose at the hinge post. The gate starts to sag, and the latch no longer lines up.
- Chain-link gate pull-backs: In the older bungalow neighborhoods with narrow driveways and minimal setbacks, a bumped gate bends the top rail or pulls the post out of plumb. Compact equipment and careful handling make the repair faster and less disruptive.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Coalinga, CA
A typical latch and alignment repair in Coalinga runs $180 to $340. Weld and frame work runs $220 to $480. Electric gate operator repair, including diagnosis, replacement of failed parts like capacitors or safety edges, and re-testing, generally falls between $250 and $650. Full replacement of a standard metal gate starts around $450, and wrought iron repair lands between $200 and $700 depending on the post and weld work required. The number you’re quoted on the phone is confirmed in writing before any work begins, and it doesn’t change unless hidden damage is found – and if that happens, you approve the new number before we proceed. Call (559) 785-2501 for a free estimate on your specific gate.
We Also Serve Cities Near Coalinga
Alongside our work in Coalinga, we handle gate repair in Lemoore, Hanford, Kerman, and Firebaugh. If you’re outside Coalinga proper, check whether your property falls in our service area by calling us. We’re part of the wider Gate Repair team serving the Central Valley, and our Coalinga coverage includes the rural roads and acreage entrances that sit well outside city limits.
Serving Coalinga, CA - Our Local Coverage Area
We’re based in the Coalinga area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Coalinga
If your gate entrance is more than about 200 feet from the house panel, running a dedicated circuit means trenching, conduit, and a secondary panel – costs that often exceed $2,000 before any gate work begins. A properly-sized solar system, with the right panel wattage and battery capacity for Coalinga’s 100°F-plus summer heat, typically runs $1,200 to $2,400 installed. In this climate, the control board and battery are the parts that need shade and airflow. Solar is usually the cheaper, cleaner answer for remote west-side entrances. Call (559) 785-2501 and we’ll walk through your specific layout.
That afternoon stall is classic thermal failure in Coalinga. The control board, mounted inside a metal housing on a south or west-facing post, heats up past its rated operating temperature in the afternoon sun. Heat-aged capacitors and cracked solder joints stop passing current reliably. The fix is replacing the heat-damaged components and adding a ventilated or shaded mount. Plan on $280 to $480 for a typical slide track and motor service, and we always inspect the board housing during that call.
Yes, and we do it often. Those original gates have dry, seasoned wood that’s often worth keeping. We add galvanized steel corner plates and heavy-angle brackets at the hinge post, pull the lag screws and re-anchor them with longer fasteners, and re-align the latch hardware. Reinforcement typically costs $250 to $450, versus $600 to $1,200 for a full replacement. If the wood has split beyond where fasteners can hold, we’ll tell you straight and give you both numbers in writing.
Yes. Photo-eye sensors are the reverse-safety mechanism that tells the operator to stop and reverse if something crosses the gate path while it’s closing. Without them, the gate will close on a vehicle, a trailer, a child, or livestock. On rural Coalinga properties, the livestock risk is real, and many homes have kids and dogs moving around the driveway. Retrofit safety edges and photo-eyes typically run $350 to $600 installed on an existing gate. We can include this in any operator repair or new installation. Call (559) 785-2501 for a written quote.
It’s a tie between sun-baked control boards and dust-packed rack-and-pinion drives. Both are made worse by the same two conditions: 100°F-plus summer heat and fine alkaline dust from oil field roads and almond orchard work. The dust grinds mechanical parts, and the heat kills electronics. On south-facing posts, we often see LiftMaster and DoorKing boards with visible solder joint fatigue after just a few Coalinga summers. The fix usually lands between $280 and $650, and you’ll see the exact number before we start.
Call Latch and Post Gate Repair for Gate Service in Coalinga
If your gate is stuck, sagging, or refusing to respond, start with a phone call. We’ll ask a few questions, give you an honest bracket of cost over the phone, and schedule a visit at a time that works for your household. Written price before work begins. Shoe covers and drop cloths inside the home. A photo of the clean-up before we leave. And the 365-Day Done Right Promise behind every job. Call (559) 785-2501 now for a free estimate.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Fresno, serving Coalinga since 2009.