Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHinge & Post Repair in Fresno, CA
Hinge and post repair in Fresno means fixing the two structural points that carry the entire weight of your gate: the hinges that let it swing and the post that keeps it standing straight. A leaning post or a sagging hinge is rarely just cosmetic – it puts uneven stress on the latch, the opener, and the gate frame itself. At Latch and Post Gate Repair Fresno, we repair or replace worn hinges, reset leaning posts, and reinforce the mount so the gate closes square again. If the problem is small, we’ll tell you. If it’s not, you’ll see a written price before we touch anything. Call (559) 785-2501 and someone will pick up, day or night.
Most hinge and post work falls under the broader umbrella of Gate Repair in Fresno, but it deserves its own focus because the fix is structural, not mechanical. This is the work we do most often for homeowners in neighborhoods like Woodward Park, Tower District, Fig Garden, and Clovis-adjacent streets where gates face a lot of wind and afternoon heat.
Key Takeaways
- Hinge and post problems get worse fast in Fresno’s hard clay soil and summer heat; fixing them early is cheaper than replacing a fallen gate.
- We provide a written price before any work starts, every visit.
- Technicians wear shoe covers, lay drop cloths inside, and send a photo of the cleanup before leaving.
- Every repair is covered by the 365-Day Done Right Promise.
- Someone answers the phone 24/7 at (559) 785-2501.
When You Need Hinge & Post Repair
You may not think about hinges and posts until the gate starts misbehaving. These are the signs we see on most Fresno service calls:
- The gate drags or scrapes the ground on the latch side. This usually means the post has leaned or the hinge side has settled. In Fresno’s clay soil, posts shift after winter rain and summer dry spells.
- The gate won’t close all the way, or it swings shut on its own. A worn top hinge lets the gate tilt. The latch no longer lines up with the striker, even if the opener works fine.
- You can see rust or cracks at the hinge welds. Weld failure on a heavy steel gate is a real safety issue. A gate that comes off its hinges weighs 200 to 600 pounds; nobody should be near it when that happens.
- The gate leans visibly toward the street or the house. That’s a post failure, not a hinge failure. The fix involves digging, re-setting, and often pouring new concrete – not just tightening bolts.
- You hear a grinding or popping sound when the gate moves. That’s metal on metal with no lubricant, or a hinge pin binding. Left alone, it chews through the hinge barrel and ruins the post mount.
- The gate moved after a strong windstorm. Fresno gets gusts off the Sierra foothills that can twist a weak post or shear a hinge bolt, especially on wide driveway gates.
Our Hinge & Post Repair Process
We keep this straightforward. You’ll know what’s happening at each step.
- Call or book, and tell us what the gate is doing. A live person answers at (559) 785-2501. We’ll ask what kind of gate it is, what it’s doing, and when it started. No script, no hold music.
- We inspect the gate, the post, and the gate’s attitude. “Attitude” just means how the gate sits in relation to the post and the ground. We check hinge wear, post lean, concrete condition, and how the latch communicates with the opener. If it’s a Viking or BFT opener, we check the limit settings because a post shift changes the geometry the opener was configured for.
- You get a written price before any work starts. This is the Cedarwell Care Promise, and it’s not optional. The price includes all labor, hardware, and cleanup.
- We do the repair, protecting the area as we work. Shoe covers go on before we step inside. Drop cloths go down over floors and any pathway we use. We ask before moving anything. If your kids are napping or your dog is anxious, we can use quiet tools and work around the noise-sensitive part of the day.
- We test the gate through a full open-close cycle, multiple times. That includes the latch alignment, hinge motion, and – where it applies – the opener’s safety sensors and force settings.
- We clean up and send you a photo of the area before we leave. You’ll see the floor as we found it. This is how we’d want it done at our own houses.
Hinge & Post Repair Pricing in Fresno
Most hinge and post repairs in Fresno fall between $180 and $640, depending on what’s actually wrong. Here’s what shapes the number:
- Hinge-only replacement: $180 to $340. This covers replacing one or two standard residential gate hinges, shimming the gate square, and lubricating the pivot points.
- Post re-setting: $320 to $640. This involves digging out the old footing, setting the post plumb in new concrete, and re-hanging the gate to close square. Fresno’s clay soil expands and contracts enough that this is a job we do at least once a week.
- Welded hinge repair on steel driveway gates: $250 to $550. We grind out the old weld, re-weld, and reinforce the mount plate when there’s enough good material. If the post is also loose, the post work is priced separately and you’ll see both numbers in writing before we start.
What moves the price: gate weight, post condition, whether the post sits in soil or concrete, whether new concrete is needed, and whether it’s a swing gate or a cantilever slide gate. A FAAC opener on a wide driveway gate often needs its limit switches recalibrated after a post repair, and that’s always included in the upfront number.
We’ll never give you a quote over the phone and change it when we arrive. The written price is generated on site, after inspection, and it’s the same number whether we fix it in an hour or three hours.
Call (559) 785-2501 for an exact quote. Estimates are free, and there’s no pressure to accept the work on the spot.
FAQs – Hinge & Post Repair
How much does hinge and post repair cost in Fresno?
Hinge-only repairs in Fresno typically run $180 to $340, while post re-setting runs $320 to $640 depending on gate weight, soil, and concrete condition. You’ll see the exact written price before any work begins. Call (559) 785-2501 for a free on-site estimate.
Can you fix a leaning gate post the same day?
Yes, in most cases a leaning post can be re-set the same day we inspect it. The catch is concrete: if we pour a new footing, the gate should not be used for 24 to 48 hours while the concrete cures. We’ll explain exactly what to expect before we start.
My gate opener is fine but the gate drags. Do I need a new opener?
No. When an opener runs fine but the gate drags or the latch won’t line up, it’s almost always a hinge or post issue, not an opener problem. We inspect the structure first before touching any BFT, Linear, or FAAC electronics, because adjusting an opener to compensate for a bad post just masks the real problem and wears out the machine. For lock repair or structural issues, we fix the root cause.
What happens if the repair fails after you leave?
We fix it. The 365-Day Done Right Promise covers every hinge and post repair we do. If it’s not right, we make it right. No argument, no fine print. Just call (559) 785-2501 and tell us what’s happening.
Why Fresno Homeowners Call Us for Hinges and Posts
Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on. We’re a home-focused gate specialist, not a general handyman. Since 2009, as part of the Cedarwell family of independently owned and operated gate specialists, we’ve repaired the gates that families in Fresno rely on every day: the side gate that keeps the dog in, the driveway gate that keeps the kids’ bikes from rolling out, the back gate that the trash service uses.
We’re factory-trained on the brands families actually own: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because a Linear actuator on a Fresno driveway gate responds differently to post movement than a Viking arm does. We’ve seen the patterns.
Our technicians are background-checked and uniformed. They operate under the Cedarwell C.A.R.E. values on every job: Clean up like it is our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work. We choose pet-safe lubricants where there’s a choice, and we can schedule around nap time if quiet matters. We’ll tell you what to protect, what to watch, and how to keep your gate healthy – in plain words, not a sales pitch.
If your gate leans, scrapes, pops, or won’t close square, call (559) 785-2501. A live person answers, day or night, every day of the year. We’ll talk through what you’re seeing, set up a visit, and give you a written price before any tool comes out of the truck.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Fresno, serving Fresno. We also offer weld & rust repair services.