Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Firebaugh, CA
Gate work in Firebaugh follows the rhythm of the valley: farm traffic, wind, and hard summer heat. We’re Latch & Post Gate Repair, part of the Cedarwell family, and we focus on the two things every gate depends on – the latch that holds it and the post that carries it. Most Firebaugh homes were built between the 1950s and 1980s, which means we see a lot of chain-link gates on pipe posts and older ornamental iron that has spent decades in dust and sun. On ranch properties, the gates are bigger, heavier, and worked harder. If your gate is sagging, dragging, or not latching, call (559) 785-2501 and we’ll give you a written price before anything gets touched.
Why Firebaugh Homes Are Different
Firebaugh’s hot, dry summers do more than dry out the soil. They bake grease out of hinges, expand and contract metal, and crack welds that looked fine in spring. The occasional strong winds push loose gates against their stops and shake hardware until bolts back out. Seasonal maintenance is not optional here – it is the difference between a gate that swings for years and one that binds in the middle of the season.
The housing stock adds another layer. Homes from the 1950s-1980s often have original chain-link gates set in concrete that has shifted over decades of irrigation and heat. Farm properties are different again: larger welded steel or pipe gates, often hung on non-standard posts. Along old Highway 33 and the back roads, we regularly see gates hung from repurposed farm equipment – an old axle, a section of drill pipe – which means custom hinge points and latch geometry that a standard parts kit will never fit. Knowing what works in Firebaugh means knowing the difference between a gate that needs a hinge rebuild and one that needs a post reset deeper in the ground.
Styles & brands we work with
Our Main Firebaugh Services
Most calls we get from Firebaugh fall into two groups: a gate that has stopped working correctly and needs Gate Repair in Firebaugh, or a property that needs a new gate built to the right size and swing. Electric systems are the third, and they have their own page below. Each service has its own dedicated Firebaugh page with pricing, timelines, and what to expect.
Gate Repair in Firebaugh
Sagging hinges, latch bolts that no longer line up, wheels that have worn flat, posts that lean with the irrigation season – these are the jobs we see every week in Firebaugh. Because many gates here sit on non-standard posts or repurposed farm steel, we carry a range of hinge bodies, wheel brackets, and latch plates so the fix doesn’t wait on a special order. We’ll straighten or reset the post, re-hang the gate, set the latch so it catches clean, and show you the before and after. Details are on the Gate Repair in Firebaugh page.
Gate Installation in Firebaugh
A new gate in Firebaugh has to be built for the conditions: post depth that accounts for expanding soil, hinges rated for a heavy gate, and hardware that tolerates dust without binding. We measure, quote a written price, and install – whether it’s a replacement chain-link gate on a 1960s home or a wider welded steel gate for a ranch entrance. We keep the workspace clean, use shoe covers and drop cloths when we step inside, and photograph the cleanup before we leave. See the full scope on the Gate Installation in Firebaugh page.
Electric Gate Repair in Firebaugh
Dust is the quiet enemy of gate operators in Firebaugh. Sensors get coated, limit switches stick, and circuit boards overheat in summer sun. We diagnose and repair operators from FAAC, BFT, Linear, and Viking, among others, and we’ll tell you honestly whether a component repair or a full operator replacement makes more sense. The Electric Gate Repair in Firebaugh page covers same-visit repairs and what parts we commonly stock for this area.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Firebaugh
We’re factory-trained on the brands Firebaugh gates actually use – FAAC, BFT, Linear, and Viking appear most often on electric and automated ranch gates here. We keep common boards, sensors, and remote receivers in our service vehicles. See our brands page for the full list, including LiftMaster, Ghost Controls, and DoorKing.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Firebaugh, CA
Prices below are the ranges we typically see in Firebaugh. Every job gets a written price before any work starts – always included, never a surprise.
| Service | Typical range in Firebaugh |
|---|---|
| Gate latch replacement (standard) | $85-$220 |
| Gate hinge replacement (pair, welded steel) | $150-$350 |
| Chain-link gate post reset (concrete) | $200-$400 |
| Weld repair (per joint, farm gate) | $75-$150 |
| Full chain-link gate installation (4-6 ft) | $450-$900 |
| Tubular steel driveway gate installation | $1,200-$3,500 |
| Welded steel ranch gate installation (12-16 ft) | $1,500-$4,000 |
| Electric operator diagnostic visit | $95-$180 |
| Operator sensor replacement | $120-$250 |
| Operator circuit board replacement | $250-$650 |
What pushes the price up in Firebaugh is usually the post. Non-standard posts made from old farm steel often need custom hinge plates or bracket fabrication, and soil that has shifted from irrigation can mean digging deeper and pouring a wider footing. You’ll see the exact number in writing before we touch anything, and the 365-Day Done Right Promise covers it after.
Neighborhoods We Serve in Firebaugh
We work across the Firebaugh area, from the older grid of streets around the downtown core to the ranch properties along the river roads and up toward the Highway 33 corridor. Typical response for repair calls in Firebaugh is same-day or next-morning, with scheduling around harvest traffic on the back roads.
- Downtown Firebaugh (16th St corridor)
- North Firebaugh (near Firebaugh High School)
- Westside / San Joaquin River roads
- Highway 33 ranch corridor
- South Firebaugh (Nees Ave area)
Service Area – Cities Near Firebaugh
If you’re outside Firebaugh, we also cover neighboring Central Valley communities. You can see specific pages for Chowchilla, CA, Kerman, CA, Los Banos, CA, and Madera, CA.
Serving Firebaugh, CA - Our Local Coverage Area
We’re based in the Firebaugh area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Firebaugh
Most repair calls in Firebaugh are scheduled same-day or next-morning. If the gate is stuck open or won’t latch at all, tell us when you call and we’ll prioritize it. Call (559) 785-2501 for the earliest available time.
For most residential driveway gates, no permit is needed. Larger ranch entrances or gates near the road right-of-way can trigger county review depending on setback and height. We’ll confirm what applies to your property before the job starts.
Yes. We schedule around equipment movement and field traffic, and we’ll coordinate a time that keeps your roads clear. Morning appointments on ranch properties usually work best during harvest, before the day’s hauling starts. Call (559) 785-2501 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Firebaugh Customers Say
"Good repair on a sagging gate. Part for the older motor took a few days, so two trips, but they explained it and were tidy and polite each time. Gate works smoothly now."
- Carmen Ulloa"Gate motor died and they replaced it carefully, cleaning every bit of debris off the driveway. Mindful not to leave the yard open with our dog out. Great crew."
- Benson Ide"Our gate opener quit and they came out quick. The tech was careful not to leave the yard open while our dog was out, which I really appreciated. Clean work, swept up the metal shavings."
- Eleanor Boggs