Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Installation Across Clovis
Gate installation in Clovis runs $1,400 – $6,800 for most residential jobs, depending on whether you need a sliding driveway gate, a swing gate, or a full automated system with new posts. We quote the exact number before any work starts, in writing, and we don’t start until you approve it. Latch and Post Gate Repair Fresno serves Clovis homeowners from Harlan Ranch to Old Town, and our crew understands the heat, dust, and soil conditions that determine whether a gate lasts five years or twenty. Call (559) 785-2501 for a free estimate.
Clovis isn’t one housing type. It’s a mix of mid-century ranch homes near downtown and newer planned communities spreading east and north. That matters for gates. A 1960s wooden gate near Old Town Clovis needs a different approach than a builder-installed wrought-iron gate in a Harlan Ranch courtyard. We’ll tell you straight up what’s worth repairing and what’s cheaper to replace.
Why Latch and Post Gate Repair Fresno Is Clovis’s Preferred Gate Installation Company
Latch and Post Gate Repair is part of the Cedarwell family of independently owned and operated gate specialists, and we’ve been doing this work since 2009. Clovis homeowners call us because we show up when we say we will, our technicians are background-checked and uniformed, and we put everything in writing before touching a hinge. No pressure. No vague estimates. Just a written price and a straight answer.
Our crews service Clovis daily. We know the streets of Harlan Ranch, the older lots off Clovis Avenue, and the gated communities along Shepherd and Fowler. When you call (559) 785-2501, a live person answers. It’s 4 p.m. on a Saturday or 2 a.m. on a Tuesday, same thing. We don’t route Clovis calls through a voicemail system, and we don’t make you wait for a callback.
We also carry the brands families in Clovis actually own: LiftMaster, FAAC, BFT, Viking, Ghost Controls, DoorKing, and Elite. Our technicians are factory-trained on these systems, so the right fix usually happens on the first visit. Every job carries the 365-Day Done Right Promise, and we back that up with shoe covers, drop cloths, and a cleanup photo before we leave. The floors stay clean, the dust stays outside, and the gate works.
Led by Cody Beckman, Latch and Post Gate Repair Fresno operates from the Central Valley office and dispatches crews to Clovis with local knowledge built into every job. We know which neighborhoods have clay-heavy soil that settles post footings, which subdivisions get dust that clogs chain drives, and which older homes still have gates hung before modern safety requirements existed.
Styles & brands we work with
Sliding Gate Installation in Clovis
Sliding gate installation in Clovis is the right choice for long driveways, corner lots, and properties where a swing gate would block the sidewalk or require too much clearance. Most Clovis jobs run $2,200 – $5,400 including the steel track, post mounting, cantilever hardware if needed, and a new operator. Sliding gates handle the flat terrain of Clovis well, but the dust from surrounding farmland means the track and chain drive need regular attention. We recommend sealed bearing rollers and a chain guard on every slide gate we install in Clovis.
Track-Mounted Slide Gates
Track-mounted slides work best on level ground with a straight run. We set the track in a compacted base and pitch it slightly so irrigation runoff from Clovis lawns doesn’t pool in the track channel.
Cantilever Slide Gates
Cantilever gates float over the ground, which matters in Clovis where decomposed granite and landscape rock end up in tracks. They cost more upfront, but in dusty subdivisions near Harlan Ranch they avoid the clogged-track callbacks that plague cheaper installations.
Gate Opener Installation in Clovis
Gate opener installation in Clovis typically runs $900 – $2,800, including the operator, low-voltage wiring, safety sensors, and programming. If it’s a retrofit onto an existing gate, expect the lower end. If we’re pulling new wire across a driveway and setting posts for photocells, the price climbs. Clovis heat is hard on opener components. We position control boards away from direct sun, use heat-rated capacitors when the budget allows, and run all low-voltage wiring in conduit.
Retrofitting an Existing Gate
Many Clovis homes built before 2000 have manual gates. We can add an opener to a structurally sound gate in a day, provided the post is still solid and the hinge hardware isn’t pulling loose. If the post is rotting at the footing or the gate has sagged more than half an inch, we’ll tell you it’s cheaper to reset the post or swap the gate than to watch a new opener fail.
New Automation for New Gates
When we install a new gate and opener together, we match the operator to the gate’s weight and wind load, not just the driveway width. In open areas near Clovis’s eastern edges, spring winds push hard against solid-panel gates. An undersized opener on a heavy wrought-iron gate is an early failure waiting to happen.
Trusted Brands We Service in Clovis
We install and service openers from FAAC, BFT, Linear, and Viking, among others. These are the builders, not the exception, in Clovis’s planned communities. We keep control boards, safety sensor kits, and remotes for these brands ready in the Central Valley office, so a Clovis job doesn’t stall waiting on a part from a distributor. If your current opener is a LiftMaster or DoorKing, we handle those too. The brand matters less than the installation details, but factory training on these systems means we know each one’s failure patterns in Clovis heat and dust.
Common Gate Installation Problems We See in Clovis Homes
- Posts rotting at the footing: In older Clovis neighborhoods with clay-heavy soil and flood irrigation, water collects at post bases. The concrete footing cracks, the post tilts, and the gate sags. We reset posts in deeper footings with gravel drainage.
- Dust-clogged chain drives: Slide gates in subdivisions near active farmland collect fine dust that grinds into chain links and sprockets. We see this weekly in newer Clovis tracts. Sealed components and a chain guard fix it.
- Surge-damaged control boards: East Clovis thunderstorms send lightning strikes into open fields. The surge travels through low-voltage landscape wiring into gate control boards. Simple surge protection on the incoming power and sensor loop prevents most of these failures.
- Faded, chalking powder coat on wrought iron: Clovis UV is unrelenting. The powder coat breaks down, moisture reaches the steel, and welds start rusting. We re-coat with a UV-rated finish and check hinge posts for corrosion before hanging a new gate.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Installation in Clovis, CA
Here’s what gate installation costs in Clovis based on the jobs we quote most often. A single swing gate with new posts runs $1,400 – $2,600. A double swing gate for a wider driveway is $2,200 – $4,200. A sliding driveway gate with track and operator lands between $3,000 and $6,800. Pedestrian gates in backyards run $800 – $1,500. These ranges reflect material costs in Clovis right now and our labor for a standard installation. Wrought iron costs more than steel tube. Automated openers add $900 – $2,800. The written quote you get before work starts includes everything: posts, hardware, operator, wiring, safety sensors, and the cleanup.
We Also Serve Cities Near Clovis
Our crews cover Clovis daily and regularly work in Gate Installation projects across the wider Central Valley. We also serve homeowners in Fresno, Sanger, Fowler, and Madera. Each job gets the same written price and cleanup routine, no matter the city.
Serving Clovis, CA - Our Local Coverage Area
We’re based in the Clovis area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Clovis
Yes in some cases, no in others. If the wooden gate is solid, the hinges aren’t pulling out, and the post hasn’t rotted at the base, we can add an opener for $900 – $2,800. If the post is soft, the gate sags, or the wood has split where hardware mounts, replacement is usually cheaper than fighting it. We’ll show you the post and explain what we’re seeing before we recommend anything. Call (559) 785-2501 for a free assessment.
Because lightning strikes nearby open fields and sends a surge through low-voltage landscape wiring that is rarely grounded properly. The control board is the first thing in the circuit to absorb it. We install surge protection on the AC input and the low-voltage loop for every opener we put in east Clovis. The cost is modest, and it prevents a $400 – $800 board replacement.
A sliding gate works when your driveway is long or flat and you don’t have room for a gate to arc open. A swing gate works on shorter driveways where the ground slopes up or the driveway has a curve. In Clovis, dust and track maintenance argue for swing gates on smaller properties, but slide gates handle long runs better. We’ll look at your driveway slope, soil, and gate weight, then give you a specific recommendation and a written price. Call (559) 785-2501 and we’ll come measure it.
Automatic gates in Clovis must have photoelectric sensors that stop and reverse the gate if anything crosses the path, plus an auto-reverse mechanism that triggers on contact. This is not optional. We test both on every installation and every service call. To check yours, block the sensor beam while the gate is closing. The gate should stop and reverse. If it doesn’t, call (559) 785-2501 and we’ll fix it same day.
Heat expands metal, and daily expansion and contraction pulls gates and sensors out of alignment. Dust works into chain drives, rollers, and limit switches. An opener that might last ten years in a mild climate often lasts six or seven in Clovis without proper protection. We position components out of direct sun, use heat-rated parts, and seal what needs sealing. The installation detail adds maybe $150 – $300 to the job and buys years of life. For an exact quote, call (559) 785-2501.
Real Experience With Clovis Gates
We recently replaced a sagging swing gate in a Harlan Ranch home where the original hinge post had rotted at the footing. The gate had pulled the post out of plumb, and the LiftMaster opener kept faulting because the safety photocells were misaligned from the daily thermal expansion of the wrought iron. We reset the post in a deeper concrete footing, swapped the worn hinges, and realigned the photocells. No more false reversals. The homeowner’s kids and dog could use the driveway again without the gate jerking and stopping halfway.
Clovis’s rapid expansion from a railroad town to a sprawling Fresno suburb means many of its newer subdivisions feature ornate, builder-installed wrought-iron gates with automated openers that must withstand intense San Joaquin Valley heat and dust. Older homes near Old Town often retain custom wooden gates from the 1950s through the 1970s that have weathered decades of prolonged sun exposure. Those two gate populations fail differently, and the retrofit-versus-replace answer depends heavily on neighborhood age and gate material. We’ll tell you which one you have and what it needs.
Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on. If you’re in Clovis and your gate sags, sticks, won’t stay closed, or the opener won’t respond, call (559) 785-2501. We’ll come out, measure it, write the price down, and you decide. No pressure. Just a clean gate and a clean driveway.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Fresno, serving Clovis since 2009 as part of the Cedarwell family of gate specialists.